O3-Setup FAQ


The document applies to users of the "O3 Mode Settings"

Product LineTenda Outdoor Wireless Bridge O3    Question Category Function Configure

Part 1Configure your computer
Part 2: Login management interface of O3
Part 3Select the proper operating mode
Mode oneAP Mode Transform your existing wired network to a wireless network.
Mode twoStation ModeActing as a “Wireless Adapter” to connect your wired devices to a wireless network.
Mode threeUniversal Repeater ModeExtend your existing wireless coverage by relaying wireless signal.
Mode fourWISPWirelessly connect to ISP station/hotspot to share Internet to local wireless and wired network.
Mode fiveRepeaterCombine multi networks via wireless connection.
Mode sixP2MP ModeCombine multi local networks via wireless connection.
Mode sevenRouter ModeWired connect to ADSL/Cable Modem via WAN port and share Internet to local wireless and wired network.
1.1 Right click icon in the lower right corner of the desktop computer, and select “Open Network and Sharing Center”.
1.2 Select and click corresponding network adapter.
1.3 Click “Status” and then click “Properties”.


1.4 Double click “Internet protocol IPV4” And select “Use the following IP address”, “192.168.2.X” X is an integer between 3~253),Subnet mask is “255.255.255.0”.
 
2.1 Login AP mode
Input 192.168.2.1 in a web browser’s address bar, and then press Enter or Return on your keyboard. Enter the default username and password (admin for both defaults) and click Login.
 
3.1 Mode One AP Mode
Click “Quick setup”, select “AP Mode”.
Custom local wireless network parameters and click next.
Confirm the information is correct, click "Save"
3.2 Mode two Station mode
    Select “Station mode” in “Quick Setup” option.
  Open scan button, select the superior wireless signal which you want to extend.
  The information in the frame as below should be the same with superior router.
 Configure local IP address, confirm it is different from superior router but in a same segment network. DNS can be reference.
   Confirm the information is correct, click "Save"
 
3.3 Mode ThreeUniversal Repeater mode
       Select “Universal Repeater mode” in” Quick Setup” option.
 Open scan button, select the superior wireless signal which you want to extend.
 The information in the frame as below should be the same with superior router.
 Configure local IP address, confirm it is different from superior router but in a same segment network. DNS can be reference.
      Confirm the information is correct, click "Save"
3.4 Mode four WISP mode
      Select “WISP mode” in “Quick Setup” option.
Open scan button, select the superior wireless signal which you want to extend.
     The information in the frame as below should be the same with superior router.
 
Select the appropriate network connection type and fill in corresponding information
Custom local wireless network parameters, as below:
Configure local IP address, confirm it is not in the same network segment with the superior router and click next.
Confirm the information is correct, click "Save"
3.5 Mode five Repeater mode
        Select “Repeater mode” in “Quick Setup” option.
Open scan button, select the superior wireless signal which you want to extend.
       The information in the frame as below should be the same with superior router.
     Configure local IP address, confirm it is different from superior router but in a same segment network. DNS can be reference.
     Confirm the information is correct, click "Save"
3.6 Mode Six P2MP mode
    Select “P2MP mode” in “Quick Setup” option.
Open scan button, select the superior wireless signal which you want to extend.
     The information in the frame as below should be the same with superior router.
     Configure local IP address, confirm it is different from superior router but in a same segment network. DNS can be reference.
     Confirm the information is correct, click "Save"
3.7 Mode Seven Router mode
Select “Router mode” in “Quick Setup” option.
Select appropriate Wan Connection Type, for example PPPOE and fill in username and password. And click next.
Custom local wireless network parameters and click next.
Confirm the information is correct, and click “Save”.


Was this article helpful to you?

Very Good(17)Article Views(6093)